Towards a Practical and Efficient Copper-Catalyzed Trifluoromethylation of Aryl Halides

The first copper-catalyzed trifluoromethylation of aryl halides was developed that utilizes inexpensive trifluoroacetates. Providing low concentrations of the most economically attractive and atom-efficient trifluoromethylation reagent this new protocol is advantageous compared to known procedures both economically and ecologically.     

The generalized amalgam method for modal reduction

In this paper, we propose an extension of the amalgam method to reduce advection diffusion problem with time dependent parameters. From a full general basis, this technique consists to select rapidly the most influent modes, and to add to them the remaining modes balanced by a coefficient. The originality of this paper lies in the fast obtention of a full degraded model, used as a reference in a minimization process of the reduced model’s error. Transcribed to the physical space, this error approaches the error between the reduced model and the real physical finite elements model. The treated application is a disk rotating at a variable velocity with time dependent thermal inputs. Comparison between the reduced and the finite elements model gives a gain in term of computational time of 36 for a mean error on the entire domain equal to 0.42%.     

Evaluation of temperature field and heat flux by inverse analysis during steel strip rolling

Knowledge of the temperature field in the roll is a critical factor of modern, high-speed rolling mills. In this paper, an inverse analytical method is developed to determine the temperature field and especially the temperature (and heat flux) at the surface of the roll by measuring the temperature with a thermocouple (fully embedded) at only one point inside the roll. Iterative methods are not studied because short computation times are desired. Some assumptions are done to resolve analytically the unsteady heat equation, taking into account the restrictions of the measurement system (e.g., measurement according to successive times). The solution is validated by comparing the outputs of the method and prescribed analytical temperature fields. Good agreement is obtained. Noise sensitivity is estimated by adding artificial random numbers to the inputs. Good accuracy is observed. A 10% error of the temperature sensor depth is also considered and does not compromise the method. On the other hand, the computation time (around 0.05 s by cycle) is studied to rapidly optimise the industrial parameters during the rolling process.     

Noise Feedback Coding Revisited： Refurbished Legacy Codecs and New Coding Models

Noise feedback coding(NFC) has attracted renewed interest with the recent standardization of backward-compatible enhancements for ITU-T G.711 and G.722.It has also been revisited with the emergence of proprietary speech codecs,such as BV16,BV32,and SILK,that have structures different from CELP coding.In this article,we review NFC and describe a novel coding technique that optimally shapes coding noise in embedded pulse-code modulation(PCM) and embedded adaptive differential PCM(ADPCM).We describe how this new technique was incorporated into the recent ITU-T G.711.1,G.711 App.III,and G.722 Annex B(G.722B) speech-coding standards.     

Design of a low-density wood-cement particleboard for interior wall finish

Gypsum boards form a very large part of the building walls and ceilings finishing market. However, they have poor screw-withdrawal resistance, low hardness and are highly sensitive to moisture. The objective of this study was to determine whether it is possible to make wood-cement particleboards of the same density as gypsum boards while avoiding these drawbacks.Wood-cement particleboards were made by pouring the wood-cement paste in a mould. This was made possible by adding a viscosity modifying mixture to the mixing water and a set accelerating mixture to improve wood/cement compatibility. The mechanical properties and surface quality of the wood-cement particleboards were improved by using, on the board surfaces, paper sheets that were the same as those used on gypsum boards.The average specific gravity of the wood-cement particleboards was the same as gypsum boards, at 0.7. The average bending modulus of rupture obtained for the wood-cement particleboards was 10 MPa in the finishing paper principal direction and 5 MPa in the other direction compared to 5.5 MPa and 1.6 MPa respectively for gypsum boards. The average screw-withdrawal resistance of wood-cement particleboards was 570 N, that is, 1.7 times higher than for gypsum boards.     

Analysis of muscle length effect on an S type motor-unit fractional multi-model

Muscle models are useful in bio-inspired robotic, because they allow to reproduce accurately natural motion. When they are used for robotic issue, they need to be compact and embeddable. The non-integer model order has the advantage to ensure a parametrical parsimony that permits to implant it easily on an embedded system. Thus, a fractional multi-model of muscle was identified and presented in later paper. This model is able to predict the response of a motor unit to an electrical stimulation, considering isometric contractions (that is to say, muscle length is constant). There are three different physiological types of motor unit (FR, FF, and S). The aim of this work is to study muscle length impact on the multi-model and the limitations of the linear multi-model. Previous paper was published using FR type motor unit. In this paper, the results of the study using S type motor unit are presented.     

Bulk and Surface Properties of Liquid Al-Li and Li-Zn Alloys

Physicochemical properties like density, surface tension, and viscosity of liquid binary Al-Li and Li-Zn alloys have been measured using draining crucible method. The experimentally measured surface-tension values have been compared to theoretical results based either on the Butler model or the compound formation model assuming the existence of the most favored A ₁ B ₂ and A ₂ B ₃ clusters. Several models for viscosity calculation have been also applied and discussed in confrontation with measured data. Finally, the clustering effects in the liquid Al-Li and Li-Zn alloys have been examined using two microscopic functions, i.e., the concentration fluctuation function in the long-wavelength limit and the Warren-Cowley short-range order parameter.     

Palm oil deodorizer distillate as toughening agent in polylactide packaging films

Polylactide (PLA) is the most used biodegradable and biobased food packaging polymer for rigid containers and films. However, its low ductility is a hurdle for increasing its applications in flexible food packaging. A solution is the use of additives. Palm oil deodorizer distillate (PODC) is revealed to be an excellent additive promoting PLA ductility. PODC is a by‐product of vegetable oil refining, which is available in stable quality and in sufficient amounts. Amorphous PLA/PODC blends had an elongation at break of around 130% and that of semi‐crystalline blends was still around 55% compared to the initial 5% of neat PLA. At the same time the PLA rigidity and high glass transition temperatures were kept. PODC was also a very efficient processing aid, allowing for film blow extrusion. The blends were stable in properties during six months without exudation. They complied with legal norms of Food Contact Materials (EU 10/2011) and induced no sensorial alteration of packed food. Therefore PODC is a very interesting alternative to common plasticizers for the production of flexible PLA packaging films. © 2016 Society of Chemical Industry